easyVDR Kopie des easyVDR-Forums zum Nachschlagen
WOL funktioniert nicht

easyVDR - >VARforumsname - >WOL funktioniert nicht

sinai  18.Nov.2008 09:17:03
Hallo zusammen

Da mein VDR in einem anderen Stockwerk steht, als mein PC, musste ich bisher immer hinlaufen und einschalten, wenn ich mal schnell was nachsehen wollte, um im Forum zu helfen.

Folglich dachte ich an WOL für den VDR

WOL ist im BIOS als automatisch aktiviert

hwinfo --netcard
20: PCI 208.0: 0200 Ethernet controller
  [Created at pci.281]
  Unique ID: rBUF.6lKL7g0K678
  Parent ID: 6NW+.siohrLUzzI4
  SysFS ID: /devices/pci0000:00/0000:00:1e.0/0000:02:08.0
  SysFS BusID: 0000:02:08.0
  Hardware Class: network
  Model: "IBM EtherExpress PRO/100 VE"
  Vendor: pci 0x8086 "Intel Corporation"
  Device: pci 0x2449 "82801BA/BAM/CA/CAM Ethernet Controller"
  SubVendor: pci 0x1014 "IBM"
  SubDevice: pci 0x0234 "EtherExpress PRO/100 VE"
  Revision: 0x03
  Driver: "e100"
  Driver Modules: "e100"
  Device File: eth0
  Memory Range: 0xee000000-0xee000fff (rw,non-prefetchable)
  I/O Ports: 0x2000-0x2fff (rw)
  IRQ: 20 (20116 events)
  HW Address: 00:09:6b:a4:66:31
  Link detected: yes
  Module Alias: "pci:v00008086d00002449sv00001014sd00000234bc02sc00i00"
  Driver Info #0:
    Driver Status: e100 is active
    Driver Activation Cmd: "modprobe e100"
  Driver Info #1:
    Driver Status: eepro100 is not active
    Driver Activation Cmd: "modprobe eepro100"
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #12 (PCI bridge)


Die Netzwerkkarte ist auf WOL geschaltet

ethtool eth0
Settings for eth0:
        Supported ports:
        Supported link modes:  10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
        Supports auto-negotiation: Yes
        Advertised link modes:  10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
        Advertised auto-negotiation: Yes
        Speed: 100Mb/s
        Duplex: Full
        Port: MII
        PHYAD: 1
        Transceiver: internal
        Auto-negotiation: on
        Supports Wake-on: g
        Wake-on: g
        Current message level: 0x00000007 (7)
        Link detected: yes


ifconfig
eth0      Protokoll:Ethernet  Hardware Adresse 00:09:6B:A4:66:31
          inet Adresse:192.168.2.202  Bcast:192.168.2.255  Maske:255.255.255.0
          inet6 Adresse: fe80::209:6bff:fea4:6631/64 G?ltigkeitsbereich:Verbindung
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:2040 errors:0 dropped:0 overruns:0 frame:0
          TX packets:2498 errors:0 dropped:0 overruns:0 carrier:0
          Kollisionen:0 Sendewarteschlangenl?nge:1000
          RX bytes:463358 (452.4 KiB)  TX bytes:711858 (695.1 KiB)


Und einmal wachte der VDR auch auf,als ich

wol 00:09:6B:A4:66:31

an meinem PC eingab. WOL ist das Tool wakeonlan für Opensuse. Leider nur einmal. Hat jemand noch eine Idee, woran es liegen könnte?

Andy
VDR 1: ASRock mit Atom J1200, NVIDIA GT610, Lüfterlos, TBS 6982 SE mit easyVDR 3.0
verleihnix  18.Nov.2008 11:32:21
Hi

Hatte die gleichen Probs mit E100 / E1000

Schau mal hier http://www.easy-vdr.de/forum/index.php?topic=3198.msg22474#msg22474
in der RCShutdown.

Mir hilfts, hab es schon mehrfach angemerkt ist aber noch nicht ins ISO eingeflossen.

Gruß Dirk


VDR-1: ATC620 , FSC1520 Cel.2G 512MB 160G, FF 2.1 , 2xKNC-S , GLCD 240x64 ,IR-Ein Rev4 , easyVDR 0.5rc1 VDR-2: ATC600 , FSC1520 Cel.2G 512MB 160G 2x400G, FF 2.1 , 2xKNC-S , GLCD 240x64 ,IR-Ein Rev4 , easyVDR 0.5rc1 TestVDR:  TUSL2C Cel.1.3G 512MB 20-80G, FF 1.3 , Nova-S oder KNC1 ,IR-Ein Rev4 , 
sinai  21.Nov.2008 16:49:46
Funktioniert perfekt. Dankeschön

Andy
VDR 1: ASRock mit Atom J1200, NVIDIA GT610, Lüfterlos, TBS 6982 SE mit easyVDR 3.0