| juecad 13.Feb.2008 18:40:35 |
Hallo zusammen,
habe seit längerem Probleme mit meinem Fernsehbild.
Meine Hardware: DVB-S Karte mit decoder von Technotrend,
Skystar 2 ohne decoder
Pundit
Folgendes Problem: Nach Neustart habe ich ein ganz normales Bild. Nach ein paar Sekunden fängt es an zu ruckeln und wird schwarz. OSD funktioniert weiterhin. Wenn ich den VDR über Menü neu starte, habe ich das gleiche Problem wieder.
Habe nun festgestellt: Wenn ich mir die Signalstärke anschaue, sieht am Anfang alles gut aus. Wenn dann das Bild weg ist, dann hat der UNC:-Wert ffffffff statt 00000000 und die gelben Kästchen unten werden ausser SIGNAL grau. Wenn ich zwischen Karte 0 und 1 umschalte funktioniert 1 einwandfrei und 0 bleibt schwarz.
Warum funktioniert die Karte 0 nach jedem Neustart einwandfrei und wird nach ein paar Sekunden schwarz?
Ich hoffe ihr habt eine Lösung für mich.
Gruß Jürgen
ASUS Pundit, TT-Premium S-2300 ff, Skystar2 lb |
| ItsMee 13.Feb.2008 18:44:26 |
Hi,
welche Karte hat das Signalproblem - Full Featured - oder Budget? Falls Budget - läuft das System wenn die Budget entfernt ist?
Wird die entsprechende Karte in der Zeit ungewöhnlich warm?
Zeigt dmesg etwas ungewöhnliches?
ItsMee
[url=http://vdr.itsmee.de/vdr2/]VDR2: EasyVDR 0.6.08 - HD-ready :)VDR3: EasyVDR 0.7.22 HD :)
P5N7A-VM / Pentium E5200 / GeForce 9300M3N78-VM / Sempron 140
vga2scart an Röhre / rsync gespiegeltes Foto ShareHDMI @ LG W2361V
Linux4Media Display mit HW patch gegen Geistertasten
[url=http://wiki.easy-vdr.de/index.php/Hilfe]Du brauchst Hilfe? Wir brauchen Daten!! |
| juecad 14.Feb.2008 04:55:43 |
Hallo,
Karte 0, also die Full featured Karte, denke ich. Pc ist schon immer sehr warm, da ich die Lüfter mit einem Widerstand gedrosselt habe. Heute Morgen habe ich den PC eingeschaltet, er war also ziemlich kalt, und habe nach ca. 30s das gleiche Problem wieder. Ich werde doch mal versuchen beide Karten einzeln laufen zu lassen. Ist halt ein kleiner Aufwand, da ich den CPU Kühler abmontieren muss.
dmesg: ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Interrupt Link (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link (IRQs 3 4 5 6 7 10 11 *12 14 15)
ACPI: PCI Interrupt Link (IRQs 3 4 5 6 7 10 11 12 14 *15)
ACPI: PCI Interrupt Link (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link (IRQs 3 4 5 *6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link (IRQs 3 4 5 6 7 10 11 12 14 15) *9
ACPI: PCI Root Bridge (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
Enabling SiS 96x SMBus.
PCI: Ignoring BAR0-3 of IDE controller 0000:00:02.5
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 13 devices
PnPBIOS: Disabled by ACPI PNP
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:02: ioport range 0xe400-0xe47f could not be reserved
pnp: 00:02: ioport range 0xe480-0xe4ff has been reserved
pnp: 00:02: ioport range 0xe600-0xe61f has been reserved
pnp: 00:02: ioport range 0x480-0x48f has been reserved
pnp: 00:0c: ioport range 0x3f0-0x3f1 has been reserved
pnp: 00:0c: ioport range 0x290-0x297 has been reserved
PCI: Ignore bogus resource 6 [0:0] of 0000:01:00.0
PCI: Bridge: 0000:00:01.0
IO window: d000-dfff
MEM window: df800000-dfffffff
PREFETCH window: e8000000-f3ffffff
PCI: Bus 2, cardbus bridge: 0000:00:10.0
IO window: 00001000-000010ff
IO window: 00001400-000014ff
PREFETCH window: 10000000-11ffffff
MEM window: 12000000-13ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt 0000:00:10.0 -> GSI 16 (level, low) -> IRQ 177
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 8192 bind 4096)
TCP reno registered
Simple Boot Flag at 0x3a set to 0x1
IA-32 Microcode Update Driver: v1.14a
Total HugeTLB memory allocated, 0
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.27 [Flags: R/W].
fuse init (API version 7.7)
cdfs 2.6.17 loaded.
JFS: nTxBlock = 1720, nTxLock = 13767
SGI XFS with ACLs, security attributes, realtime, no debug enabled
SGI XFS Quota Management subsystem
OCFS2 1.3.3
OCFS2 Node Manager 1.3.3
OCFS2 DLM 1.3.3
OCFS2 DLMFS 1.3.3
OCFS2 User DLM kernel interface loaded
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
vesafb: framebuffer at 0xe8000000, mapped to 0xce980000, using 1875k, total 32768k
vesafb: mode is 800x600x16, linelength=1600, pages=7
vesafb: protected mode interface info at cb3d:0008
vesafb: pmi: set display start = c00cb412, set palette = c00cb468
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 100x37
fb0: VESA VGA frame buffer device
ACPI: Power Button (FF)
ACPI: Power Button (CM)
ACPI: Invalid PBLK length
ACPI: Getting cpuindex for acpiid 0x1
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SIS5513: IDE controller at PCI slot 0000:00:02.5
ACPI: PCI Interrupt 0000:00:02.5 -> GSI 16 (level, low) -> IRQ 177
SIS5513: chipset revision 0
SIS5513: not 100% native mode: will probe irqs later
SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
ide0: BM-DMA at 0xa400-0xa407, BIOS settings: hda:DMA, hdb:DMA
Probing IDE interface ide0...
hda: SAMSUNG SP1614N, ATA DISK drive
hdb: TOSHIBA DVD-ROM SD-M1612, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hda: max request size: 512KiB
hda: 312581808 sectors (160041 MB) w/8192KiB Cache, CHS=19457/255/63
hda: cache flushes supported
hda: hda1 hda2 hda3 hda4
hdb: ATAPI 48X DVD-ROM drive, 512kB Cache
Uniform CD-ROM driver Revision: 3.20
megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
megaraid: 2.20.4.9 (Release Date: Sun Jul 16 12:27:22 EST 2006)
megasas: 00.00.03.01 Sun May 14 22:49:52 PDT 2006
3ware 9000 Storage Controller device driver for Linux v2.26.02.007.
libata version 2.00 loaded.
RocketRAID 3xxx SATA Controller driver v1.0 (060426)
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
device-mapper: multipath: version 1.0.4 loaded
device-mapper: multipath round-robin: version 1.0.0 loaded
device-mapper: multipath emc: version 0.0.3 loaded
EISA: Probing bus 0 at eisa.0
Cannot allocate resource for EISA slot 1
Cannot allocate resource for EISA slot 8
EISA: Detected 0 cards.
TCP bic registered
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI Shortcut mode
Time: tsc clocksource has been installed.
ACPI: (supports S0 S1 S3 S4 S5)
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 344k freed
NET: Registered protocol family 1
Adding 265032k swap on /dev/hda1. Priority:-1 extents:1 across:265032k
v4l1_compat: no version for "struct_module" found: kernel tainted.
Linux video capture interface: v2.00
EXT3 FS on hda3, internal journal
saa7146: register extension 'dvb'.
ACPI: PCI Interrupt 0000:00:13.0 -> GSI 18 (level, low) -> IRQ 185
saa7146: found saa7146 @ mem ce924000 (revision 1, irq 185) (0x13c2,0x0000).
DVB: registering new adapter (Technotrend/Hauppauge WinTV DVB-S rev1.X or Fujitsu Siemens DVB-C).
adapter has MAC addr = 00:d0:5c:00:79:89
dvb-ttpci: info @ card 0: firm f0240009, rtsl b0250018, vid 71010068, app 80f22623
dvb-ttpci: firmware @ card 0 supports CI link layer interface
dvb-ttpci: adac type set to 0 @ card 0
saa7146_vv: saa7146 (0): registered device video0
saa7146_vv: saa7146 (0): registered device vbi0
ves1x93: Detected ves1893a rev2
DVB: registering frontend 0 (VLSI VES1x93 DVB-S)...
input: DVB on-card IR receiver as /class/input/input0
dvb-ttpci: found av7110-0.
b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded successfully
flexcop-pci: will use the HW PID filter.
flexcop-pci: card revision 1
ACPI: PCI Interrupt 0000:00:0e.0 -> GSI 17 (level, low) -> IRQ 193
DVB: registering new adapter (FlexCop Digital TV device).
b2c2-flexcop: MAC address = 00:d0:d7:03:1d:08
b2c2-flexcop: i2c master_xfer failed
b2c2-flexcop: i2c master_xfer failed
b2c2-flexcop: i2c master_xfer failed
mt352_read_register: readreg error (reg=127, ret==-121)
b2c2-flexcop: i2c master_xfer failed
nxt200x: nxt200x_readbytes: i2c read error (addr 0x0a, err == -121)
Unknown/Unsupported NXT chip: 00 00 00 00 00
b2c2-flexcop: i2c master_xfer failed
lgdt330x: i2c_read_demod_bytes: addr 0x59 select 0x02 error (ret == -121)
b2c2-flexcop: i2c master_xfer failed
b2c2-flexcop: i2c master_xfer failed
stv0297_readreg: readreg error (reg == 0x80, ret == -121)
b2c2-flexcop: found the vp310 (aka mt312) at i2c address: 0x0e
DVB: registering frontend 1 (Zarlink VP310 DVB-S)...
b2c2-flexcop: initialization of 'Sky2PC/SkyStar 2 DVB-S (old version)' at the 'PCI' bus controlled by a 'FlexCopII' complete
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
USB Universal Host Controller Interface driver v3.0
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt 0000:00:03.0 -> GSI 20 (level, low) -> IRQ 169
ohci_hcd 0000:00:03.0: OHCI Host Controller
ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:03.0: irq 169, io mem 0xde800000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
b44.c:v1.01 (Jun 16, 2006)
ACPI: PCI Interrupt 0000:00:0f.0 -> GSI 18 (level, low) -> IRQ 185
eth0: Broadcom 4400 10/100BaseT Ethernet 00:11:2f:54:5f:bd
ACPI: PCI Interrupt 0000:00:03.1 -> GSI 21 (level, low) -> IRQ 201
ohci_hcd 0000:00:03.1: OHCI Host Controller
ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:03.1: irq 201, io mem 0xde000000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:03.2 -> GSI 22 (level, low) -> IRQ 209
ohci_hcd 0000:00:03.2: OHCI Host Controller
ohci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:03.2: irq 209, io mem 0xdd800000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:03.3 -> GSI 23 (level, low) -> IRQ 217
ehci_hcd 0000:00:03.3: EHCI Host Controller
ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 4
PCI: cache line size of 128 is not supported by device 0000:00:03.3
ehci_hcd 0000:00:03.3: irq 217, io mem 0xdd000000
ehci_hcd 0000:00:03.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
NET: Registered protocol family 17
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
i2c_adapter i2c-1: SMBus Quick command not supported, can't probe for chips
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
lirc_dev: IR Remote Control driver registered, at major 61
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected SiS 651 chipset
agpgart: AGP aperture is 64M @ 0xe0000000
lirc_serial: auto-detected active low receiver
lirc_dev: lirc_register_plugin: sample_rate: 0
sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0xe600
ieee1394: Initialized config rom entry `ip1394'
ACPI: PCI Interrupt 0000:00:02.3 -> GSI 17 (level, low) -> IRQ 193
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ= MMIO= Max Packet= IR/IT contexts=
ieee1394: Host added: ID:BUS[0-00:1023] GUID
eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
ACPI: PCI Interrupt 0000:00:02.7 -> GSI 18 (level, low) -> IRQ 185
intel8x0_measure_ac97_clock: measured 50045 usecs
intel8x0: clocking to 48000
lirc_serial: AIEEEE: your clock just jumped backwards
lirc_serial: 0 1 47b3b858 47b3b85e 7527a 32c61
Yenta: CardBus bridge found at 0000:00:10.0 [1524:1411]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:10.0, mfunc 0x00000202, devctl 0x44
Yenta: ISA IRQ mask 0x0ca8, PCI irq 177
Socket status: 30000006
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
usbcore: registered new driver kbtab
drivers/usb/input/kbtab.c: v0.0.2:USB KB Gear JamStudio Tablet driver
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
Gruß Jürgen
ASUS Pundit, TT-Premium S-2300 ff, Skystar2 lb |
| sigvdr 14.Feb.2008 12:41:47 |
Hallo,
hast du mal versucht die SAT-Kabel zu tauschen ? Evtl. gibts auch nur Kabelprobleme!
Gruß Sig
VDR Server: MB: Asrock N3150-ITX, CPU N3150, DVB-S2: DD-S8, Festplatte (3xSeagate->geschrottet) jetzt 2TB WD, easyVDR3.5
VDR-Clients: Raspberry PI2 oder PI3, Raspbian Stretch mit VDR 2.2.0
|
| juecad 15.Feb.2008 21:59:16 |
Hallo,
wenn ich die Kabel an meinen normalen Sat-Reciever anschließe, funktioniert er bei beide Kabeln.
Werde wohl doch eine SatKarte kaufen, kann diese dann ja wieder zurückschicken wenn es dann immer noch nicht funktioniert.
Könnt ihr mir eine gute, günstige full featured Karte empfehlen? Und wo soll ich sie dann kaufen? Bin überhaupt nicht auf dem aktuelen Stand der Dinge.
Gruß Jürgen
ASUS Pundit, TT-Premium S-2300 ff, Skystar2 lb |
| sigvdr 17.Feb.2008 21:31:30 |
Hallo,
b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded successfully
flexcop-pci: will use the HW PID filter.
flexcop-pci: card revision 1
ACPI: PCI Interrupt 0000:00:0e.0 -> GSI 17 (level, low) -> IRQ 193
DVB: registering new adapter (FlexCop Digital TV device).
b2c2-flexcop: MAC address = 00:d0:d7:03:1d:08
b2c2-flexcop: i2c master_xfer failed
b2c2-flexcop: i2c master_xfer failed
b2c2-flexcop: i2c master_xfer failed
mt352_read_register: readreg error (reg=127, ret==-121)
b2c2-flexcop: i2c master_xfer failed
nxt200x: nxt200x_readbytes: i2c read error (addr 0x0a, err == -121)
Unknown/Unsupported NXT chip: 00 00 00 00 00
b2c2-flexcop: i2c master_xfer failed
lgdt330x: i2c_read_demod_bytes: addr 0x59 select 0x02 error (ret == -121)
b2c2-flexcop: i2c master_xfer failed
b2c2-flexcop: i2c master_xfer failed
stv0297_readreg: readreg error (reg == 0x80, ret == -121)
b2c2-flexcop: found the vp310 (aka mt312) at i2c address: 0x0e
DVB: registering frontend 1 (Zarlink VP310 DVB-S)...
b2c2-flexcop: initialization of 'Sky2PC/SkyStar 2 DVB-S (old version)' at the 'PCI' bus controlled by a 'FlexCopII' complete
wenn ich mir den Bereich anschaue dann sieht die Budget-Karte aber problematisch aus.
läuft das System wenn die Budget entfernt ist?
hast du das schon getestet ?
Gruß Sig
VDR Server: MB: Asrock N3150-ITX, CPU N3150, DVB-S2: DD-S8, Festplatte (3xSeagate->geschrottet) jetzt 2TB WD, easyVDR3.5
VDR-Clients: Raspberry PI2 oder PI3, Raspbian Stretch mit VDR 2.2.0
|
| juecad 18.Feb.2008 22:00:18 |
Danke für die Antwort.
Habe die Budget Karte entfernt, hat nichts gebracht.
habe nun dei TT Premium S-2300 modded bestellt.
Muss ich da was mit dem Treiber machen?
Gruß Jürgen
ASUS Pundit, TT-Premium S-2300 ff, Skystar2 lb |
| juecad 25.Feb.2008 19:27:11 |
Hallo,
habe nun mein TT-S 2300 Karte bekommen und eingebaut. Und siehe da, alles läuft wieder tatellos.
Gruß Jürgen
ASUS Pundit, TT-Premium S-2300 ff, Skystar2 lb |
